entfoki.blogg.se - Repetier server and wanhao duplicator 4s

Repetier server and wanhao duplicator 4s Patch#
Repetier server and wanhao duplicator 4s mods#
Repetier server and wanhao duplicator 4s software#
Repetier server and wanhao duplicator 4s code#
Repetier server and wanhao duplicator 4s plus#

Detection of heater/thermistor decoupling.

Important parameters are stored in EEPROM and can easily be modified without.

Autodetect the command protocol, so it will work with any host software.

Standard ASCII and improved binary (Repetier protocol) communication.

Support for Arduino Due based boards allowing much faster speeds.

Fast - 40000 Hz and more stepper frequency is possible with a 16 MHz AVR.

Nozzle pressure control for improved print quality with RAMPS.

Trajectory smoothing for smoother lines.

Supports cartesian, delta and core xy/yz printers.

Some ideas were also taken from Teacup, Grbl and Marlin. Which based on Tonokip RepRap firmware rewrite based off of Hydra-mmm firmware. This firmware is a nearly complete rewrite of the sprinter firmware by kliment Repetier-Firmware is a firmware for RepRap like 3d-printer powered with

Repetier server and wanhao duplicator 4s plus#

plus several small contributions from other users.

Repetier server and wanhao duplicator 4s code#

sdavi (first u8glib code implementation).Martin Croome (first delta implementation).It was initially based on the Sprinter firmware from Kliment, but the code has run The sources are managed by the Hot-World GmbH & Co. Separation of logic and hardware access to allow different processor architecturesįor documentation please visit Developer.Long filename support (from Glenn Kreisel).WARNING: This version only compiles with older Arduino IDE 1.0.x, for New homing sequence with preheat for nozzle based z sensors.Many minor corrections and improvements.Decoupling test for heater and sensor for more safety.Correction of parallelogram distortions.Pulse dense modulation for heater and fans.More stable temperature control with PID.New gcode handler for more flexible support of different inputs.Dual X axis support (2 separate x axis).Improved event system to extend firmware without modification of files.New parameter are initalized with default values. This is handy for updates as you get all newly introduced parameter just by uploading the old version and downloading the This system also allows it to upload configurations created with this tool and modify the configuration. You get the complete sources you need to compile from the online configurator. Or for latest 1.0.x development version atįor easy and fast configuration. To keep every release workable, but as work in progress there is no guarantee.

Repetier server and wanhao duplicator 4s mods#

The changes and there may be bigger mods with an update. the version should be considered alpha stage. To benefit already from improvements achieved. Will get several changes and only users with programming skills will do it manually We assume until a config tool is available the configuration That way it gets much faster to search the right place.

Split long files like boards, displays, languages in several files into a subfolder.

But that requires a different configuration at several parts. We will try to keepĬommands and communication identical to 1.0, but for the configuration we seeĪ much more flexible way that makes it much easier to adjust the firmware to Version 2 will be a incompatible refactoring of version 1.0. Where all the new features will be added. Official 1.0 version we will start developing version 2.0 in the branch dev2

Repetier server and wanhao duplicator 4s Patch#

Moved to stable after a while as 1.0.x patch updates. Fixes for this will be done in the dev branch and

New configurations since we need to add them also to our online tool, so users

Document what your pull request will change/fix/introduce.

Only pins.h/fastio.h/hal.*Īnd configuration.h are architecture dependent, so changes there need to be made In fact we develop on avr and just copy them to due. So for mostĬhanges modifications need to be in both folders.

We have two folders for different processor architectures.

Options, add them to the official configuration.h file.

Do not include your personal configuration files.

From time to time we push these to master This is where we addĪnd test new features and bug fixes.

Only send pull requests against development version.

To allow easy integration of new features you should follow some simple Hardware related and many things can only be implemented/tested with the right Like contributions from other sources, especially since the firmware is very

Repetier server and wanhao duplicator 4s software#

This software is open source licensed under the GPL V3. Repetier-Firmware - the fast and user friendly firmware Notes for developers/pull requests